Thermal Analysis of Flip-Chip Bonding Designs for GaN Power HEMTs with an On-Chip Heat-Spreading Layer.

In this work, we demonstrated the thermal analysis of different flip-chip bonding designs for high power GaN HEMT developed for power electronics applications, such as power converters or photonic driver applications, with large gate periphery and chip size, as well as an Au metal heat-spreading layer deposited on top of a planarized dielectric/passivation layer above the active region. The Au bump patterns can be designed with high flexibility to provide more efficient heat dissipation from the large GaN HEMT chips to an AlN package substrate heat sink with no constraint in the alignment between the HEMT cells and the thermal conduction bumps. Steady-state thermal simulations were conducted to study the channel temperatures of GaN HEMTs with various Au bump patterns at different levels of current and voltage loadings, and the results were compared with the conventional face-up GaN die bonding on an AlN package substrate. The simulations were started from a single finger isolated HEMT cell and then extended to multiple fingers HEMT cells (total gate width > 40 mm) to investigate the "thermal cross-talk" effect from neighboring devices. Thermal analysis of the GaN HEMT under pulse operation was also performed to better reflect the actual conditions in power conversion or pulsed laser driver applications. Our analysis provides a combinational assessment of power GaN HEMT dies under a working condition (e.g., 1MHz, 25% duty cycle) with different flip chip packaging schemes. The analysis indicated that the channel temperature rise (∆T) of a HEMT cell in operation can be reduced by 44~46% by changing from face-up die bonding to a flip-chip bonding scheme with an optimized bump pattern design.

Modified Distributed Bragg Reflectors for Color Stability in InGaN Red Micro-LEDs.

The monolithic integration of InGaN-based micro-LEDs is being of interest toward developing full-color micro-displays. However, the color stability in InGaN red micro-LED is an issue that needs to be addressed. In this study, the modified distributed Bragg reflectors (DBRs) were designed to reduce the transmission of undesired spectra. The calculated optical properties of the InGaN red micro-LEDs with conventional and modified DBRs have been analyzed, respectively. The CIE 1931 color space and the encoded 8-bit RGB values are exhibited for the quantitative assessment of color stability. The results suggest the modified DBRs can effectively reduce the color shift, paving the way for developing full-color InGaN-based micro-LED displays.

Buffer Traps Effect on GaN-on-Si High-Electron-Mobility Transistor at Different Substrate Voltages.

Substrate voltage (VSUB) effects on GaN-on-Si high electron mobility transistors (HEMTs) power application performance with superlattice transition layer structure was investigated. The 2DEG conductivity and buffer stack charge redistribution can be affected by neutral/ionized donor and acceptor traps. As the donor/acceptor traps are excessively ionized or de-ionized by applying VSUB, the depletion region between the unintentionally doped (UID)/Carbon-doped (C-doped) GaN layer may exhibit a behavior similar to the p-n junction. An applied negative VSUB increases the concentration of both the ionized donor and acceptor traps, which increases the breakdown voltage (BV) by alleviating the non-uniform distribution of the vertical electric field. On the other hand, an applied positive VSUB causes the energy band bending flattener to refill the ionized traps and slightly improves the dynamic Ron degradation. Moreover, the amount of electrons injected into the buffer stack layer from the front side (2DEG channel/Ohmic contact) and the back side (AlN nucleation layer/superlattice transition layer) are asymmetric. Therefore, different VSUB can affect the conductivity of 2DEG through the field effect, buffer trapping effect, and charge redistribution, which can change the electrical performance of the device.

Performance Analyses of Photonic-Crystal Surface-Emitting Laser: Toward High-Speed Optical Communication.

This study conducts comprehensive performance analyses of a commercial photonic-crystal surface-emitting laser (PCSEL) via small-signal measurement and the bit-error-rate test. Meanwhile, the radio frequency characteristics of the PCSEL are unveiled for the first time. Compared to the vertical-cavity surface-emitting lasers, the PCSEL shows great potential for a broader optical bandwidth that is benefited from the high optical-confinement factor. A maximum bandwidth of around 2.32 GHz is experimentally observed when the PCSEL was biased at 340 mA. Moreover, a theoretical calculation was applied to shed light on the characteristics of the small-signal measurement, providing a deep insight into the corresponding intrinsic response model. The signal transmission capability of the PCSEL was investigated as well. The maximum bit rate and corresponding rise time transmitted at 500 Mbps are 1.2 Gbps and 186.16 ps, respectively. Thus, a high-speed PCSEL can be realised with a shrunk form factor, serving as a promising candidate for the next-generation light sources in high-speed optical communication.

Ultracompact Nanophotonics: Light Emission and Manipulation with Metasurfaces.

Internet of Things (IoT) technology is prosperous for the betterment of human well-being. With the expeditious needs of miniature functional devices and systems for adaptive optics and light manipulation at will, relevant sensing techniques are thus in the urgent stage of development. Extensive developments in ultrathin artificial structures, namely metasurfaces, are paving the way for the next-generation devices. A bunch of tunable and reconfigurable metasurfaces with diversified catalogs of mechanisms have been developed recently, enabling dynamic light modulation on demand. On the other hand, monolithic integration of metasurfaces and light-emitting sources form ultracompact meta-devices as well as exhibiting desired functionalities. Photon-matter interaction provides revolution in more compact meta-devices, manipulating light directly at the source. This study presents an outlook on this merging paradigm for ultracompact nanophotonics with metasurfaces, also known as metaphotonics. Recent advances in the field hold great promise for the novel photonic devices with light emission and manipulation in simplicity.

Defect Inspection Techniques in SiC.

With the increasing demand of silicon carbide (SiC) power devices that outperform the silicon-based devices, high cost and low yield of SiC manufacturing process are the most urgent issues yet to be solved. It has been shown that the performance of SiC devices is largely influenced by the presence of so-called killer defects, formed during the process of crystal growth. In parallel to the improvement of the growth techniques for reducing defect density, a post-growth inspection technique capable of identifying and locating defects has become a crucial necessity of the manufacturing process. In this review article, we provide an outlook on SiC defect inspection technologies and the impact of defects on SiC devices. This review also discusses the potential solutions to improve the existing inspection technologies and approaches to reduce the defect density, which are beneficial to mass production of high-quality SiC devices.

Gateway towards recent developments in quantum dot-based light-emitting diodes.

Quantum dots (QDs), with their excellent photoluminescence, narrow emission linewidth, and wide color coverage, provide unrivaled advantages for advanced display technologies, enabling full-color micro-LED displays. It is indeed critical to have a fundamental understanding of how QD properties affect micro-LED display performance in order to develop the most energy-efficient display device in the near future. However, to take a more detailed look at the stability issues and passivation ways of QDs is essential for accelerating the commercialization of QD-based LED technologies. Knowing about the most recent breakthroughs in QD-based LEDs can give a good indication of how they might be used in shaping the future of displays. In this review, we discuss the characteristics of QD-based LEDs for the applications of display and lighting technologies. Various approaches for synthesis and the stability improvement of QDs are addressed in detail, along with recent advancements towards QD-based LED breakthroughs. Moreover, we summarize our latest research findings in QD-based LEDs, providing valuable information about the potential of QD-based LEDs for future display technologies.

Correction: Huang et al. High-Uniform and High-Efficient Color Conversion Nanoporous GaN-Based Micro-LED Display with Embedded Quantum Dots. Nanomaterials 2021, 11, 2696.

The authors wish to make following corrections in this paper [...].

High-Uniform and High-Efficient Color Conversion Nanoporous GaN-Based Micro-LED Display with Embedded Quantum Dots.

Quantum dot (QD)-based RGB micro-LED technology is seen as one of the most promising approaches towards full color micro-LED displays. In this work, we present a novel nanoporous GaN (NP-GaN) structure that can scatter light and host QDs, as well as a new type of micro-LED array based on an NP-GaN embedded with QDs. Compared to typical QD films, this structure can significantly enhance the light absorption and stability of QDs. As a result, the green and red QDs exhibited light conversion efficiencies of 90.3% and 96.1% respectively, leading to improvements to the luminous uniformity of the green and red subpixels by 90.7% and 91.2% respectively. This study provides a viable pathway to develop high-uniform and high-efficient color conversion micro-LED displays.

Recent Advances in Two-Dimensional Quantum Dots and Their Applications.

Two-dimensional quantum dots have received a lot of attention in recent years due to their fascinating properties and widespread applications in sensors, batteries, white light-emitting diodes, photodetectors, phototransistors, etc. Atomically thin two-dimensional quantum dots derived from graphene, layered transition metal dichalcogenide, and phosphorene have sparked researchers' interest with their unique optical and electronic properties, such as a tunable energy bandgap, efficient electronic transport, and semiconducting characteristics. In this review, we provide in-depth analysis of the characteristics of two-dimensional quantum dots materials, their synthesis methods, and opportunities and challenges for novel device applications. This analysis will serve as a tipping point for learning about the recent breakthroughs in two-dimensional quantum dots and motivate more scientists and engineers to grasp two-dimensional quantum dots materials by incorporating them into a variety of electrical and optical fields.

Breakthrough to Non-Vacuum Deposition of Single-Crystal, Ultra-Thin, Homogeneous Nanoparticle Layers: A Better Alternative to Chemical Bath Deposition and Atomic Layer Deposition.

Most thin-film techniques require a multiple vacuum process, and cannot produce high-coverage continuous thin films with the thickness of a few nanometers on rough surfaces. We present a new "paradigm shift" non-vacuum process to deposit high-quality, ultra-thin, single-crystal layers of coalesced sulfide nanoparticles (NPs) with controllable thickness down to a few nanometers, based on thermal decomposition. This provides high-coverage, homogeneous thickness, and large-area deposition over a rough surface, with little material loss or liquid chemical waste, and deposition rates of 10 nm/min. This technique can potentially replace conventional thin-film deposition methods, such as atomic layer deposition (ALD) and chemical bath deposition (CBD) as used by the Cu(In,Ga)Se2 (CIGS) thin-film solar cell industry for decades. We demonstrate 32% improvement of CIGS thin-film solar cell efficiency in comparison to reference devices prepared by conventional CBD deposition method by depositing the ZnS NPs buffer layer using the new process. The new ZnS NPs layer allows reduction of an intrinsic ZnO layer, which can lead to severe shunt leakage in case of a CBD buffer layer. This leads to a 65% relative efficiency increase.

Crystalline Engineering Toward Large-Scale High-Efficiency Printable Cu(In,Ga)Se2 Thin Film Solar Cells on Flexible Substrate by Femtosecond Laser Annealing Process.

Ink-printing method emerges as a viable way for manufacturing large-scale flexible Cu(In,Ga)Se2 (CIGS) thin film photovoltaic (TFPV) devices owing to its potential for the rapid process, mass production, and low-cost nonvacuum device fabrication. Here, we brought the femtosecond laser annealing (fs-LA) process into the ink-printing CIGS thin film preparation. The effects of fs-LA treatment on the structural and optoelectronic properties of the ink-printing CIGS thin films were systematically investigated. It was observed that, while the film surface morphology remained essentially unchanged under superheating, the quality of crystallinity was significantly enhanced after the fs-LA treatment. Moreover, a better stoichiometric composition was achieved with an optimized laser scanning rate of the laser beam, presumably due to the much reduced indium segregation phenomena, which is believed to be beneficial in decreasing the defect states of InSe, VSe, and InCu. Consequently, the shunt leakage current and recombination centers were both greatly decreased, resulting in a near 20% enhancement in photovoltaic conversion efficiency.

A Comprehensive Study of One-Step Selenization Process for Cu(In1-x Ga x )Se2 Thin Film Solar Cells.

In this work, aiming at developing a rapid and environmental-friendly process for fabricating CuIn1-x Ga x Se2 (CIGS) solar cells, we demonstrated the one-step selenization process by using selenium vapor as the atmospheric gas instead of the commonly used H2Se gas. The photoluminescence (PL) characteristics indicate that there exists an optimal location with superior crystalline quality in the CIGS thin films obtained by one-step selenization. The energy dispersive spectroscopy (EDS) reveals that the Ga lateral distribution in the one-step selenized CIGS thin film is intimately correlated to the blue-shifted PL spectra. The surface morphologies examined by scanning electron microscope (SEM) further suggested that voids and binary phase commonly existing in CIGS films could be successfully eliminated by the present one-step selenization process. The agglomeration phenomenon attributable to the formation of MoSe2 layer was also observed. Due to the significant microstructural improvement, the current-voltage (J-V) characteristics and external quantum efficiency (EQE) of the devices made of the present CIGS films have exhibited the remarkable carrier transportation characteristics and photon utilization at the optimal location, resulting in a high conversion efficiency of 11.28%. Correlations between the defect states and device performance of the one-step selenized CIGS thin film were convincingly delineated by femtosecond pump-probe spectroscopy.

In-Situ Probing Plasmonic Energy Transfer in Cu(In, Ga)Se2 Solar Cells by Ultrabroadband Femtosecond Pump-Probe Spectroscopy.

In this work, we demonstrated a viable experimental scheme for in-situ probing the effects of Au nanoparticles (NPs) incorporation on plasmonic energy transfer in Cu(In, Ga)Se2 (CIGS) solar cells by elaborately analyzing the lifetimes and zero moment for hot carrier relaxation with ultrabroadband femtosecond pump-probe spectroscopy. The signals of enhanced photobleach (PB) and waned photoinduced absorption (PIA) attributable to surface plasmon resonance (SPR) of Au NPs were in-situ probed in transient differential absorption spectra. The results suggested that substantial carriers can be excited from ground state to lower excitation energy levels, which can reach thermalization much faster with the existence of SPR. Thus, direct electron transfer (DET) could be implemented to enhance the photocurrent of CIGS solar cells. Furthermore, based on the extracted hot carrier lifetimes, it was confirmed that the improved electrical transport might have been resulted primarily from the reduction in the surface recombination of photoinduced carriers through enhanced local electromagnetic field (LEMF). Finally, theoretical calculation for resonant energy transfer (RET)-induced enhancement in the probability of exciting electron-hole pairs was conducted and the results agreed well with the enhanced PB peak of transient differential absorption in plasmonic CIGS film. These results indicate that plasmonic energy transfer is a viable approach to boost high-efficiency CIGS solar cells.

Toward omnidirectional light absorption by plasmonic effect for high-efficiency flexible nonvacuum Cu(In,Ga)Se2 thin film solar cells.

We have successfully demonstrated a great advantage of plasmonic Au nanoparticles for efficient enhancement of Cu(In,Ga)Se2(CIGS) flexible photovoltaic devices. The incorporation of Au NPs can eliminate obstacles in the way of developing ink-printing CIGS flexible thin film photovoltaics (TFPV), such as poor absorption at wavelengths in the high intensity region of solar spectrum, and that occurs significantly at large incident angle of solar irradiation. The enhancement of external quantum efficiency and photocurrent have been systematically analyzed via the calculated electromagnetic field distribution. Finally, the major benefits of the localized surface plasmon resonances (LSPR) in visible wavelength have been investigated by ultrabroadband pump-probe spectroscopy, providing a solid evidence on the strong absorption and reduction of surface recombination that increases electron-hole generation and improves the carrier transportation in the vicinity of pn-juction.

Growth and characterization of Cu(In,Ga)Se2 thin films by nanosecond and femtosecond pulsed laser deposition.

In this work, CuIn1 - x Ga x Se2 (CIGS) thin films were prepared by nanosecond (ns)- and femtosecond (fs)-pulsed laser deposition (PLD) processes. Different film growth mechanisms were discussed in perspective of the laser-produced plasmas and crystal structures. The fs-PLD has successfully improved the inherent flaws, Cu2 - x Se, and air voids ubiquitously observed in ns-PLD-derived CIGS thin films. Moreover, the prominent antireflection and excellent crystalline structures were obtained in the fs-PLD-derived CIGS thin films. The absorption spectra suggest the divergence in energy levels of radiative defects brought by the inhomogeneous distribution of elements in the fs-PLD CIGS, which has also been supported by comparing photoluminescence (PL) spectra of ns- and fs-PLD CIGS thin films at 15 K. Finally, the superior carrier transport properties in fs-PLD CIGS were confirmed by fs pump-probe spectroscopy and four-probe measurements. The present results indicate a promising way for preparing high-quality CIGS thin films via fs-PLD.

Non-antireflective scheme for efficiency enhancement of Cu(In,Ga)Se2 nanotip array solar cells.

We present systematic works in characterization of CIGS nanotip arrays (CIGS NTRs). CIGS NTRs are obtained by a one-step ion-milling process by a direct-sputtering process of CIGS thin films (CIGS TF) without a postselenization process. At the surface of CIGS NTRs, a region extending to 100 nm in depth with a lower copper concentration compared to that of CIGS TF has been discovered. After KCN washing, removal of secondary phases can be achieved and a layer with abundant copper vacancy (V(Cu)) was left. Such compositional changes can be a benefit for a CIGS solar cell by promoting formation of Cd-occupied Cu sites (Cd(Cu)) at the CdS/CIGS interface and creates a type-inversion layer to enhance interface passivation and carrier extraction. The raised V(Cu) concentration and enhanced Cd diffusion in CIGS NTRs have been verified by energy dispersive spectrometry. Strengthened adhesion of Al:ZnO (AZO) thin film on CIGS NTRs capped with CdS has also been observed in SEM images and can explain the suppressed series resistance of the device with CIGS NTRs. Those improvements in electrical characteristics are the main factors for efficiency enhancement rather than antireflection.

Observation of unusual optical transitions in thin-film Cu(In,Ga)Se2 solar cells.

In this paper, we examine photoluminescence spectra of Cu(In,Ga)Se(2) (CIGS) via temperature-dependent and power-dependent photoluminescence (PL). Donor-acceptor pair (DAP) transition, near-band-edge transition were identified by their activation energies. S-shaped displacement of peak position was observed and was attributed to carrier confinement caused by potential fluctuation. This coincides well with the obtained activation energy at low temperature. We also present a model for transition from V(Se) to V(In) and to V(Cu) which illustrates competing mechanisms between DAPs recombinations.

Ultrafast carrier dynamics in Cu(In,Ga)Se2 thin films probed by femtosecond pump-probe spectroscopy.

Ultrafast carrier dynamics in Cu(In,Ga)Se2 films are investigated using femtosecond pump-probe spectroscopy. Samples prepared by direct sputtering and co-evaporation processes, which exhibited remarkably different crystalline structures and free carrier densities, were found to result in substantially different carrier relaxation and recombination mechanisms. For the sputtered CIGS films, electron-electron scattering and Auger recombination was observed, whereas for the co-evaporated CIGS films, bandgap renormalization accompanied by band filling effect and hot phonon relaxation was observed. The lifetime of defect-related recombination in the co-evaporated CIGS films is much longer than that in the direct-sputtered CIGS films, reflecting a better quality with higher energy conversion efficiency of the former.

Observation of unusual optical transitions in thin-film Cu(In,Ga)Se2 solar cells.

In this paper, we examine photoluminescence spectra of Cu(In,Ga)Se(2) (CIGS) via temperature-dependent and power-dependent photoluminescence (PL). Donor-acceptor pair (DAP) transition, near-band-edge transition were identified by their activation energies. S-shaped displacement of peak position was observed and was attributed to carrier confinement caused by potential fluctuation. This coincides well with the obtained activation energy at low temperature. We also present a model for transition from V(Se) to V(In) and to V(Cu) which illustrates competing mechanisms between DAPs recombinations.